-
1 щит промежуточного распределения электроэнергии
- subdistribution low-voltage switchboard
- sub-distribution switchboard
- secondary distribution switchgear
- secondary distribution switchboard
щит промежуточного распределения электроэнергии
НКУ промежуточного распределения электроэнергии
-
[Интент]
Рис. ABBПараллельные тексты EN-RU
These assemblies are usually provided with one incoming unit and many outgoing units.
The apparatus housed inside the assembly are mainly molded-case circuit-breakers and/or miniature circuitbreakers.
The rated currents and the short-circuit currents of secondary distribution switchgear are lower than those of primary distribution switchgear.
The constructional models provide for the use of metal or insulating material enclosures and can be both floor- or wall-mounted, according to dimensions and weight.
In case the assemblies are used by unskilled persons, the Standard IEC 60439-3 is to be applied.
The distribution boards (ASD) are subject to the additional prescriptions of the Standard IEC 60439-3.
[ABB]Данные НКУ обычно имеют один вводной и много выводных блоков.
Внутри такого НКУ смонтированы в основном автоматические выключатели в литом корпусе и/или модульные автоматические выключатели.
Номинальные токи и токи короткого замыкания НКУ промежуточного распределения меньше чем у комплектных устройств первичного распределения электроэнергии.
Данные НКУ изготавливают в металлической или пластмассовой оболочке для установки на полу или на стене в зависимости от их размера и массы.
Если НКУ промежуточного распределения электроэнергии предназначены для установки в местах доступных неквалифицированному персоналу, то они должны соответствовать требованиям стандарта МЭК 60439-3.
[Перевод Интент]Тематики
- НКУ (шкафы, пульты,...)
Синонимы
EN
Русско-английский словарь нормативно-технической терминологии > щит промежуточного распределения электроэнергии
-
2 КРУЭ
1) Military: комплексные распределительные устройства2) Power engineering: GIS - Gas Insulated Switchgear, SF6 insulated switchgear/control gear3) Electric machinery: Secondary Distribution Switchgear, SF6 insulated, Switchgear for Secondary Distribution Systems, SF6 insulated, комплектное распределительное устройство КРУЭ с элегазовыми выключателями4) Electrical engineering: GIS, Gas Insulated Substation, комплектное распределительное устройство с элегазовой изоляцией -
3 комплектное устройство первичного распределения электроэнергии
комплектное устройство первичного распределения электроэнергии
-
[Интент]
Рис. ABBПараллельные тексты EN-RU
They are usually installed on the load side of MV/LV transformers or generators.
These assemblies include one or more incoming units, bus ties and a relatively reduced number of outgoing units.
There are also present measuring instruments and other switching and control equipment.
These assemblies have a sturdy structure to withstand the electrodynamic stresses and the weight of big sized apparatus.
As a matter of fact peculiar characteristics of the power center are high rated currents and shortcircuit currents.
The constructional type is a cubicle structure, with metal enclosure and sections divided into compartments with selective access.
[ABB]Такие устройства обычно подключают на стороне нагрузки СВ/НВ трансформаторов или генераторов.
В их состав входят один или несколько блоков ввода, шины и относительно небольшое число блоков вывода.
В состав комплектного устройства первичного распределения электроэнергии входят также измерительные приборы, коммутационные устройства и средства контроля состояния.
Данные комплектные устройства имеют прочную конструкцию, способную выдерживать электродинамическое действие токов и вес крупногабаритной аппаратуры.
Центры распределения электроэнергии характеризуются высокими номинальным током и током короткого замыкания.
С точки зрения конструктивного исполнения они представляют собой многошкафное комплектное устройство в металлической оболочке, состоящее из секций, каждая из которых разделена на отсеки с независимым доступом.
[Перевод Интент]Safety enclosed boards are used for most new installations. Common terms used to designate equipment of this type are metal-enclosed switchgear and metal-clad switchgear.
Most safety enclosed boards are of the unit or sectional type. They consist of a combination of the desired number and type of standardized unit sections.
Each section is a standard factory-assembled combination of a formed steel panel and apparatus mounted on a steel framework.
Safety enclosed switchgear may be classified with respect to purpose of application as follows:
1. General medium- or high-voltage switchgear
2. Primary unit substations
3. Rectifier unit substations
4. Secondary unit substations or power centers
5. General low-voltage switchgear
6. Low-voltage distribution switchboards
7. Motor-control-center switchboards
[American electricians’ handbook]Тематики
- НКУ (шкафы, пульты,...)
- комплектное распред. устройство (КРУ)
EN
Русско-английский словарь нормативно-технической терминологии > комплектное устройство первичного распределения электроэнергии
-
4 блок кольцевой магистрали
блок кольцевой магистрали
БКМ
-
[Интент]EN
ring main unit in electrical power distribution
A standard piece of switchgear in distribution systems comprising of switches for switching power cable rings and of switches in series with fuses for the protection of distrbution transformers. RMU: Ring Main Unit. RMU used for H.T.side. RMU is having 3no.s of switches(Circuit Breakers or Isolators or LBS), it is used for two inputs with mechanical or electrical interlock and one outgoing to the load. Either one input with two outgoings. RMU used for redundancy feeder's purpose.
Ring main unit is used in a secondary distribution system. It is basically used for an uninterrupted power supply. Alongside, it also protects your secondary side transformer from the occasional transient currents. Depending on your applications and loading conditons you can use a swicth fuse combination or a circuit breaker to protect the transformer. This transformer connected to the switch fuse/ circuit breaker is called your T off. In a common arrangement you have Load break swicthes on both the sides of your T off. Ring main Units come in standard ratings of 11/22/33 kV, 630/1250 A, 21 KA/3 secs.
[ http://wiki.answers.com/Q/What_is_a_ring_main_unit_in_electrical_power_distribution]Тематики
EN
Русско-английский словарь нормативно-технической терминологии > блок кольцевой магистрали
-
5 НКУ защищенное
- safety enclosed switchgear
- safety enclosed board
- enclosed switchboard
- enclosed assembly (of switchgear and controlgear)
НКУ защищенное
НКУ закрытое со всех сторон (за возможным исключением монтажной поверхности), в котором после его установки обеспечивается степень защиты не менее IP2X.
[ ГОСТ Р 51321. 1-2000 ( МЭК 60439-1-92)]
защищенное НКУ
НКУ, конструкция которого обеспечивает требуемую степень защиты со всех сторон от прикосновения к частям, находящимся под напряжением (за исключением монтажной поверхности).
[ ГОСТ Р МЭК 61439.1-2013]EN
enclosed assembly (of switchgear and controlgear)
an assembly enclosed on all sides, top and bottom in such a manner as to provide a specified degree of protection
NOTE – The mounting surface may form a part of the enclosure when specified in the relevant publication.
[IEV number 441-12-02]FR
ensemble (d'appareillage de connexion et de commande)
sous enveloppe
ensemble comportant une paroi sur toutes ses faces latérales, supérieure et inférieure, de façon à assurer un degré de protection spécifié
NOTE – La surface de montage peut faire partie de l'enveloppe lorsqu'une publication particulière le spécifie.
[IEV number 441-12-0
Шкаф - защищенное НКУ, предназначенное для установки на полу
Safety enclosed boards are used for most new installations. Common terms used to designate equipment of this type are metal-enclosed switchgear and metal-clad switchgear.
Most safety enclosed boards are of the unit or sectional type. They consist of a combination of the desired number and type of standardized unit sections.
Each section is a standard factory-assembled combination of a formed steel panel and apparatus mounted on a steel framework.
Safety enclosed switchgear may be classified with respect to purpose of application as follows:
1. General medium- or high-voltage switchgear
2. Primary unit substations
3. Rectifier unit substations
4. Secondary unit substations or power centers
5. General low-voltage switchgear
6. Low-voltage distribution switchboards
7. Motor-control-center switchboards
[American electricians’ handbook]Тематики
- НКУ (шкафы, пульты,...)
Классификация
>>>Обобщающие термины
Синонимы
EN
- enclosed assembly (of switchgear and controlgear)
- enclosed switchboard
- safety enclosed board
- safety enclosed switchgear
DE
FR
Русско-английский словарь нормативно-технической терминологии > НКУ защищенное
-
6 комплектное распределительное устройство среднего напряжения
комплектное распределительное устройство среднего напряжения
-Safety enclosed boards are used for most new installations. Common terms used to designate equipment of this type are metal-enclosed switchgear and metal-clad switchgear.
Most safety enclosed boards are of the unit or sectional type. They consist of a combination of the desired number and type of standardized unit sections.
Each section is a standard factory-assembled combination of a formed steel panel and apparatus mounted on a steel framework.
Safety enclosed switchgear may be classified with respect to purpose of application as follows:
1. General medium- or high- voltage switchgear
2. Primary unit substations
3. Rectifier unit substations
4. Secondary unit substations or power centers
5. General low-voltage switchgear
6. Low-voltage distribution switchboards
7. Motor-control-center switchboards
[American electricians’ handbook]
Medium-voltage switchgear (Fig. 4.115) provides for the required control and metering equipment for generators, transformer supply circuits, feeders, large motors, etc., for systems with voltage up to 15,000 V. A large variety of standardized units is available
FIGURE 4.115 Medium-voltage metal-enclosed switchgear. [Westinghouse Electric Corp.][American electricians’ handbook]
Тематики
- комплектное распред. устройство (КРУ)
Синонимы
EN
Русско-английский словарь нормативно-технической терминологии > комплектное распределительное устройство среднего напряжения
-
7 НКУ защищенное
НКУ защищенное
НКУ закрытое со всех сторон (за возможным исключением монтажной поверхности), в котором после его установки обеспечивается степень защиты не менее IP2X.
[ ГОСТ Р 51321. 1-2000 ( МЭК 60439-1-92)]
защищенное НКУ
НКУ, конструкция которого обеспечивает требуемую степень защиты со всех сторон от прикосновения к частям, находящимся под напряжением (за исключением монтажной поверхности).
[ ГОСТ Р МЭК 61439.1-2013]EN
enclosed assembly (of switchgear and controlgear)
an assembly enclosed on all sides, top and bottom in such a manner as to provide a specified degree of protection
NOTE – The mounting surface may form a part of the enclosure when specified in the relevant publication.
[IEV number 441-12-02]FR
ensemble (d'appareillage de connexion et de commande)
sous enveloppe
ensemble comportant une paroi sur toutes ses faces latérales, supérieure et inférieure, de façon à assurer un degré de protection spécifié
NOTE – La surface de montage peut faire partie de l'enveloppe lorsqu'une publication particulière le spécifie.
[IEV number 441-12-0
Шкаф - защищенное НКУ, предназначенное для установки на полу
Safety enclosed boards are used for most new installations. Common terms used to designate equipment of this type are metal-enclosed switchgear and metal-clad switchgear.
Most safety enclosed boards are of the unit or sectional type. They consist of a combination of the desired number and type of standardized unit sections.
Each section is a standard factory-assembled combination of a formed steel panel and apparatus mounted on a steel framework.
Safety enclosed switchgear may be classified with respect to purpose of application as follows:
1. General medium- or high-voltage switchgear
2. Primary unit substations
3. Rectifier unit substations
4. Secondary unit substations or power centers
5. General low-voltage switchgear
6. Low-voltage distribution switchboards
7. Motor-control-center switchboards
[American electricians’ handbook]Тематики
- НКУ (шкафы, пульты,...)
Классификация
>>>Обобщающие термины
Синонимы
EN
- enclosed assembly (of switchgear and controlgear)
- enclosed switchboard
- safety enclosed board
- safety enclosed switchgear
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > НКУ защищенное
-
8 НКУ защищенное
НКУ защищенное
НКУ закрытое со всех сторон (за возможным исключением монтажной поверхности), в котором после его установки обеспечивается степень защиты не менее IP2X.
[ ГОСТ Р 51321. 1-2000 ( МЭК 60439-1-92)]
защищенное НКУ
НКУ, конструкция которого обеспечивает требуемую степень защиты со всех сторон от прикосновения к частям, находящимся под напряжением (за исключением монтажной поверхности).
[ ГОСТ Р МЭК 61439.1-2013]EN
enclosed assembly (of switchgear and controlgear)
an assembly enclosed on all sides, top and bottom in such a manner as to provide a specified degree of protection
NOTE – The mounting surface may form a part of the enclosure when specified in the relevant publication.
[IEV number 441-12-02]FR
ensemble (d'appareillage de connexion et de commande)
sous enveloppe
ensemble comportant une paroi sur toutes ses faces latérales, supérieure et inférieure, de façon à assurer un degré de protection spécifié
NOTE – La surface de montage peut faire partie de l'enveloppe lorsqu'une publication particulière le spécifie.
[IEV number 441-12-0
Шкаф - защищенное НКУ, предназначенное для установки на полу
Safety enclosed boards are used for most new installations. Common terms used to designate equipment of this type are metal-enclosed switchgear and metal-clad switchgear.
Most safety enclosed boards are of the unit or sectional type. They consist of a combination of the desired number and type of standardized unit sections.
Each section is a standard factory-assembled combination of a formed steel panel and apparatus mounted on a steel framework.
Safety enclosed switchgear may be classified with respect to purpose of application as follows:
1. General medium- or high-voltage switchgear
2. Primary unit substations
3. Rectifier unit substations
4. Secondary unit substations or power centers
5. General low-voltage switchgear
6. Low-voltage distribution switchboards
7. Motor-control-center switchboards
[American electricians’ handbook]Тематики
- НКУ (шкафы, пульты,...)
Классификация
>>>Обобщающие термины
Синонимы
EN
- enclosed assembly (of switchgear and controlgear)
- enclosed switchboard
- safety enclosed board
- safety enclosed switchgear
DE
FR
Русско-французский словарь нормативно-технической терминологии > НКУ защищенное
-
9 распределительная подстанция
1) Engineering: distribution station (электрическая), secondary substation2) oil&gas: switchgear3) Aluminium industry: distribution substation (РП)4) Electrical engineering: distribution substationУниверсальный русско-английский словарь > распределительная подстанция
См. также в других словарях:
щит промежуточного распределения электроэнергии — НКУ промежуточного распределения электроэнергии [Интент] Рис. ABB Параллельные тексты EN RU These assemblies are usually provided with one incoming unit and many outgoing units. The apparatus housed inside the assembly are mainly molded case… … Справочник технического переводчика
щит промежуточного распределения электроэнергии — НКУ промежуточного распределения электроэнергии [Интент] Рис. ABB Параллельные тексты EN RU These assemblies are usually provided with one incoming unit and many outgoing units. The apparatus housed inside the assembly are mainly molded case… … Справочник технического переводчика
комплектное устройство первичного распределения электроэнергии — [Интент] Рис. ABB Параллельные тексты EN RU They are usually installed on the load side of MV/LV transformers or generators. These assemblies include one or more incoming units, bus ties and a relatively reduced number of outgoing units. There… … Справочник технического переводчика
блок кольцевой магистрали — БКМ [Интент] EN ring main unit in electrical power distribution A standard piece of switchgear in distribution systems comprising of switches for switching power cable rings and of switches in series with fuses for the protection of distrbution… … Справочник технического переводчика
Power engineering — Power engineering, also called power systems engineering, is a subfield of electrical engineering that deals with the generation, transmission and distribution of electric power as well as the electrical devices connected to such systems… … Wikipedia
комплектное распределительное устройство среднего напряжения — Safety enclosed boards are used for most new installations. Common terms used to designate equipment of this type are metal enclosed switchgear and metal clad switchgear. Most safety enclosed boards are of the unit or sectional type. They consist … Справочник технического переводчика
НКУ защищенное — НКУ закрытое со всех сторон (за возможным исключением монтажной поверхности), в котором после его установки обеспечивается степень защиты не менее IP2X. [ГОСТ Р 51321.1 2000 (МЭК 60439 1 92)] защищенное НКУ НКУ, конструкция которого обеспечивает… … Справочник технического переводчика
НКУ защищенное — НКУ закрытое со всех сторон (за возможным исключением монтажной поверхности), в котором после его установки обеспечивается степень защиты не менее IP2X. [ГОСТ Р 51321.1 2000 (МЭК 60439 1 92)] защищенное НКУ НКУ, конструкция которого обеспечивает… … Справочник технического переводчика
НКУ защищенное — НКУ закрытое со всех сторон (за возможным исключением монтажной поверхности), в котором после его установки обеспечивается степень защиты не менее IP2X. [ГОСТ Р 51321.1 2000 (МЭК 60439 1 92)] защищенное НКУ НКУ, конструкция которого обеспечивает… … Справочник технического переводчика
НКУ защищенное — НКУ закрытое со всех сторон (за возможным исключением монтажной поверхности), в котором после его установки обеспечивается степень защиты не менее IP2X. [ГОСТ Р 51321.1 2000 (МЭК 60439 1 92)] защищенное НКУ НКУ, конструкция которого обеспечивает… … Справочник технического переводчика
Battery (electricity) — For other uses, see Battery (disambiguation). Various cells and batteries (top left to bottom right): two AA, one D, one handheld ham radio battery, two 9 volt (PP3), two AAA, one C, one … Wikipedia